Changing the settings Launching utilities mode If utilities mode is launched while the unit and a computer are connected by a USB cable, the set status may not be displayed properly. The “MIDI Controller Settings” can be set in the utilities mode. This unit automatically switches operation as shown below depending on whether or not rekordbox dj is running. ! When rekordbox is running, controller operation depends on the rekordbox dj functions. ! When rekordbox dj is not running, this controller operates as a gen- eral MIDI controller. Even if rekordbox dj is running, this controller can forcibly be operated as a general MIDI controller. 1 Disconnect the USB cable from the computer. 2 Press the [u] switch on the rear panel of this unit to set the unit to standby. This unit enters standby mode. 3 While pressing both the [SHIFT] and [PLAY/PAUSE f] buttons on the left deck, press the [u] switch on the rear panel of this unit. Utilities mode is launched. 4 Press the [SLIP REVERSE] button on the left deck. ! [SLIP REVERSE] button (not lit): Automatically switches operation depending on whether or not rekordbox is running. ! [SLIP REVERSE] button (lit): Forcibly operates as a general MIDI controller regardless of whether or not rekordbox is running. 5 Press the [u] switch on the rear panel of this unit to set the unit to standby. To save the settings, set the [u] switch on the rear panel of this unit to standby and quit utilities mode. Changing the settings with rekordbox The settings required for the DJ player can be changed with rekordbox. Change the setting items in [Controller] of [Preferences]. ! The following settings can be changed only when rekordbox and this unit are connected. Setting items in the [Deck] tab of [Controller] Ring Brightness setting Sets the brightness of the JOG RING illumination. You can switch the setting from a level of 1 to 3. The jog ring does not illuminate when set to Off. ! Set to 1 for the darkest illumination, and 3 for the brightest illumination. Jog > Brightness of the display setting Sets the brightness of the jog display section. 5 levels from 1 to 5 are available for this setting. ! Set to 1 for the darkest illumination, and 5 for the brightest illumination. Display setting for the jog display You can change the information displayed in the jog display section. Display Artwork When the [Display Artwork] check box is selected, the display is enabled and the artwork for the track loaded from rekordbox is displayed on the jog display. Display CUE SCOPE When the [Display CUE SCOPE] check box is selected, the display is enabled and the CUE SCOPE is displayed on the jog display. Time Mode The information displayed for the time display can be switched with [Time Mode]. ! Elapsed: With 0:00 as the starting point of the track, displays the time elapsed from the beginning to the current playback position. ! Remaining: With 0:00 as the end of the track, displays the time remaining to the end from the current playback position. Slip Mode Flashing Changes the slip mode flashing setting. — Enable: The buttons that can be operated only while slip mode is on flash (the [HOT CUE] button, the [4 BEAT LOOP/EXIT] button, etc.). — Disable: The buttons that can be operated only while slip mode is on do not flash. Slip button LED while slip mode is on Sets the lighting operation of the [SLIP] button for when slip mode is on. — Light is On: The [SLIP] button lights up when slip mode is on, and flashes while slip mode is being operated. — Blink: The [SLIP] button does not light up when slip mode is on. Setting items in the [Mixer] tab of [Controller] Fader Start setting Changes the fader start function setting. ! By default, this is enabled. When the [Activate the fader start when moving a channel fader or the cross fader while pressing the SHIFT button.] check box is selected, the function is enabled. Cross Fader Curve setting Switches the characteristics of the crossfader curve. ! The further the control is turned clockwise, the sharper the curve rises. ! The further the control is turned counterclockwise, the more gradu- ally the curve rises. Cross Fader Cut Lag setting Adjust the play (cut lag) of both ends of the crossfader. Adjustment can be made from 0.3 mm to 5.5 mm in 0.1 mm increments. ! By default, the level is set to 1.0 mm. 26 En
Download PDF file
Table of contents