Changing the settings Launching utilities mode If the utilities mode is launched while the unit and a computer are connected by a USB cable, the set status may not be displayed properly. ! ! ! Effect parameter 1 button lit: Channel fader starts with the sync mode set (The sync function is activated simultaneously when channel fader starting starts.) Effect parameter 2 button lit: Channel fader starts without the sync mode set (The sync function is not activated when channel fader starting starts.) Effect parameter 3 button lit: Channel fader start function disabled 1 Disconnect the USB cable from your computer. 2 Press the [STANDBY/ON] switch on this unit’s rear panel to set this unit’s power to standby. Set this unit’s power to the standby mode. Changing the crossfader start setting The crossfader start function settings can be changed. ! By default, the crossfader start mode functions without sync mode set. Changing the settings 3 While pressing both the [SHIFT] and [PLAY/PAUSE f] buttons on the left deck, press the [STANDBY/ON] switch on this unit’s rear panel. Utilities mode is launched. Press one of the effect parameter buttons on the right deck. 4 After setting this unit to the utility settings mode, operate the controller for the item whose settings you want to change. See the explanations below for the settings that can be changed. ! ! ! 5 Press the [STANDBY/ON] switch on this unit’s rear panel to set this unit’s power to standby. To save the settings, set the [STANDBY/ON] switch on this unit’s rear panel to standby and quit utilities mode. Effect parameter 1 button lit: Crossfader starts with the sync mode set (The sync function is activated simultaneously when crossfader starting starts.) Effect parameter 2 button lit: Crossfader starts without the sync mode set (The sync function is not activated simultaneously when crossfader starting starts.) Effect parameter 3 button lit: Crossfader start function disabled Setting the master output’s attenuator level ! The default is 0 dB. Utilities modes The following settings can be changed: ! MIDI controller setting ! Channel fader start setting ! Crossfader start setting ! Master output attenuator level setting ! Slip mode flashing setting ! [SLIP] button lit/flash operation setting ! Demo mode setting ! Setting of the velocity curve in velocity sampler mode ! Velocity sampler mode after-touch setting ! Operation setting of the [NEEDLE SEARCH] pad ! Cut lag setting of crossfader ! Output setting of microphone to booth monitor ! Jog dial illumination mode setting ! Back spin length setting ! Operation setting of microphone sound low cut filter ! Operation setting of crossfader MIDI message Press one of the left deck’s [HOT CUE] mode, [ROLL] mode or [SLICER] mode buttons. ! ! ! [HOT CUE] mode button lit: 0 dB (no attenuation) [ROLL] mode button lit: –3 dB [SLICER] mode button lit: –6 dB Changing the slip mode flashing setting When the slip mode is on, the buttons that can be operated in the slip mode (jog dial indicator, [AUTO LOOP] button, [PLAY/PAUSE f] button, etc.) flash. This setting can be used to disable the flashing of these buttons. ! By default, slip mode flashing is enabled. Press the [SLIP] button on the left deck. ! ! [SLIP] button lit: Slip mode flashing enabled [SLIP] button off: Slip mode flashing disabled Forcefully using the unit as the general MIDI controller The unit automatically changes operation as follows depending on whether Serato DJ is running. ! When Serato DJ is running, controller operation depends on the Serato DJ functions. ! When Serato DJ is not running, the unit operates as a general MIDI controller. Even though Serato DJ is running, you can forcefully operate the unit as a general MIDI controller. Setting the [SLIP] button lit/flash operation By default, the [SLIP] button lights when you switch to the slip mode and flashes while playback is continuing in the background. With this setting, the [SLIP] button can be made to flash when Slip mode is started, regardless of whether or not normal playback continues while the original rhythm is maintained in the background. Press the [SLIP] button on the right deck. ! ! [SLIP] button lit: The [SLIP] button flashes upon entering slip mode [SLIP] button off: The [SLIP] button lights upon entering slip mode and the [SLIP] button flashes while normal playback is continued while the original rhythm is maintained in the background. Press the [HOT CUE] or [ROLL] mode button on the right deck. ! ! [HOT CUE] mode button lit: Operation automatically changes depending on whether or not Serato DJ is running. [ROLL] mode button lit: Regardless of whether or not Serato DJ is running, the unit is forcefully operated as a general MIDI controller. Changing the demo mode setting On this unit, the demo mode is set if no operation is performed for 10 minutes under normal usage conditions. This demo mode can be changed. ! By default, demo mode starts when there is no operation for 10 minutes. ! When any control or button on this unit is operated while in the demo mode, the demo mode is canceled. Changing the channel fader start setting The channel fader start function’s setting can be changed. ! By default, the channel fader start mode functions without the sync mode set. Press one of the effect parameter buttons on the left deck. Press the [AUTO LOOP] button on the right deck. The demo mode setting changes each time the [AUTO LOOP] button is pressed. The currently set value is indicated by how the [LOOP 1/2X], [LOOP 2X], [LOOP IN] and [LOOP OUT] buttons light. ! [LOOP 1/2X] button lights: Demo mode is disabled ! [LOOP 2X] button lights: Demo mode starts when there is no operation for 1 minute ! [LOOP IN] button lights: Demo mode starts when there is no operation for 5 minutes ! [LOOP OUT] button lights: Demo mode starts when there is no operation for 10 minutes En 23
Download PDF file