CONNECTIONS (CONNECTION PANEL) CONNECTIONS CONNECTION PANEL 1 2 3 4 5 6 7 8 SIGNAL GND MASTER 2 POWER OFF ON SIGNAL GND PHONO LINE PHONO CD LINE CD DIGITAL IN L REC PHONO LINE L CONTROL L CONTROL L CONTROL L CONTROL MIDI OUT DIGITAL OUT fs (Hz) 48 k 96 k 1GND 2HOT 3COLD R R AC IN DIGITAL LINE MASTER ATT 0dB -3dB -6dB -12dB R DIGITAL LINE R DIGITAL CD R DIGITAL CD R MASTER 1 L ADD CUT MIC SIGNAL R BOOTH (TRS) L R SEND L(MONO) R RETURN L(MONO) 21 20 19 18 17 16 15 14 13 12 11 10 9 1. POWER switch 2. MASTER 2 output connectors RCA type unbalanced output. 14. SEND output connectors Ø6.3 mm phone-type output connectors. Use to connect to the input connectors of external effectors or other similar components. When the L channel only is connected, a L+R monaural signal is output. 3. Recording output connectors (REC) RCA type output connectors for recording. 4. PHONO input connectors RCA type phono level (MM cartridge) input connectors. Do not use for inputting line level signals. 15. CONTROL connectors Ø3.5 mm mini-connector. Use to connect to the control connector of a Pioneer DJ CD player. When the connectors are connected, the DJM-800’s fader can be used to perform start/stop on the DJ CD player. 5. LINE input connectors RCA type line level input connectors. Use to connect a cassette deck or other line level output component. 16. BOOTH monitor output connectors Ø6.3 mm phone-type booth monitor output connectors. The sound level from these connectors is controlled independently by the BOOTH MONITOR level dial, regardless of the position of the MASTER LEVEL dial. (These connectors are TRS output, so they support both balanced and unbalanced outputs.) 6. Signal grounding terminals (SIGNAL GND) Use to connect ground wires from analog players. This is not a safety grounding terminal. 7. CD input connectors RCA type line level input connectors. Use to connect a DJ CD player or other line level output component. 17. DIGITAL/LINE input selector switches Use to select either analog input (LINE) or digital input (DIGITAL IN). 8. DIGITAL IN connectors RCA type digital coaxial input connectors. Use to connect to DJ CD player or other digital coaxial output connectors. 18. Master output attenuator switch (MASTER ATT) Use to attenuate the level of the master 1 and master 2 outputs. Selectable values are 0 dB, –3 dB, –6 dB and –12 dB. 9. MIDI OUT connector DIN type output connector. Use to connect to other MIDI component (see P. 19). 19. Microphone signal switch (MIC SIGNAL ADD/CUT) When set to the [ADD] position, the sounds from microphone 1 and microphone 2 are output to the BOOTH monitor output connectors. When set to the [CUT] position, the sounds from microphone 1 and microphone 2 are not output to the BOOTH monitor output connectors. 10. DIGITAL OUT connector RCA type digital coaxial output connector. Master audio digital output. 11. Sampling frequency selector switch (fs 48 k/96 k) Use to set the sampling frequency of the digital output to 96 kHz/24bit or 48 kHz/24-bit. 20. MASTER 1 output connectors XLR type (male) balanced output. ÷ When using a cord with RCA-type plug, users are recommended to connect the plug directly to the MASTER 2 connectors without using an XLR/RCA converter plug. 12. DIGITAL/CD input selector switches Use to select either analog input (CD) or digital input (DIGITAL IN). 13. RETURN connectors Ø6.3 mm phone-type input connectors. Use to connect to the output connectors of external effectors or similar components. When the L channel only is connected, the L channel input is simultaneously input to the R channel. 21. Power inlet (AC IN) Use the accessory power cord to connect to an AC power outlet of the proper voltage. 4 <DRB1392> En
Download PDF file