4 5 Set the cue on the DJ player. Set the crossfader. The DJ player pauses playback at the cue point. Playback starts on the DJ player. ! If you set the crossfader back to the original position, the player instantaneously returns to the cue point already set and pauses playback (back cue). Advanced Operations About PRO DJ LINK When a PRO DJ LINK-compatible Pioneer DJ player (CDJ-2000, CDJ-900 etc.), a computer on which rekordbox is installed and this unit are connected by LAN cable, the PRO DJ LINK functions below can be used. For more details on the PRO DJ LINK function, also refer to the DJ player’s handling instructions and rekordbox’s operating instructions. For instructions on connections, see Connecting input terminals on page 8. ! When connected using a switching hub, up to 4 DJ players and 2 computers can be connected. ! Use a 100Base-TX-compatible switching hub. Some switching hubs may not operate properly. ! Set the DJ player’s player number to the same number as the channel to which the audio cable is connected. Using a microphone 1 Connect a microphone to the [MIC1] or [MIC2] terminal. Operations 2 Set the [OFF, ON, TALK OVER] selector switch to [ON] or [TALK OVER]. ! ! — [ON]: The indicator lights. — [TALK OVER]: The indicator flashes. When set to [TALK OVER], the sound of channels other than the [MIC] channel is attenuated by 18 dB (default) when a sound of -10 dB or greater is input to the microphone. The [TALK OVER] sound attenuation level can be changed at [USER SETUP]. For instructions on changing this, see Changing the settings on page 23. LINK MONITOR With this function, rekordbox music files stored on the computer can be quickly monitored over the headphones. 3 Turn the [MIC1 LEVEL] or [MIC2 LEVEL] control. Adjust the level of the sound output from the [MIC] channel. ! Pay attention that rotating to the extreme right position outputs a very loud sound. STATUS INFORMATION This function informs the DJ players of the connected channel status (on-air status, channel number, etc.). 4 Input audio signals to the microphone. Adjusting the sound quality Turn the [MIC] channels’ [EQ (HI, LOW)] controls. Refer to Specifications on page 26 for the range of sound that can be adjusted by each control. QUANTIZE When tracks analyzed with rekordbox are used, the track is put on beat even when the [ON/OFF] button of [BEAT EFFECTS] is pressed or the [X-PAD] is touched roughly. FADER START Switching between monaural and stereo audio This switches the sound output from the [MASTER1], [MASTER2], [BOOTH], [REC OUT], [PHONES], [DIGITAL MASTER OUT] and [USB] terminals between monaural and stereo. ! To adjust the sound output from the [USB] terminals, select [REC OUT] at [Mixer Audio Output] in the setting utility. Playback on the DJ player can be started by operating this unit’s fader (Fader Start Play). SOUND COLOR FX These effects change in association with the [COLOR] controls for the different channels. Switch the [MONO, STEREO] selector switch. — [MONO]: Outputs monaural audio. — [STEREO]: Outputs stereo audio. 1 Press one of the [SOUND COLOR FX] buttons. Adjusting the L/R balance of audio The left/right balance of the sound output from the [MASTER1], [MASTER2], [BOOTH], [REC OUT], [PHONES], [DIGITAL MASTER OUT] and [USB] terminals can be adjusted. ! To adjust the sound output from the [USB] terminals, select [REC OUT] at [Mixer Audio Output] in the setting utility. This selects the type of effect. The button that was pressed flashes. ! For the types of effects, see Types of SOUND COLOR FX effects on page 18. ! The same effect is set for [CH1] to [CH4]. 2 Turn the [COLOR] control. The effect is applied to the channel(s) for which the control(s) was (were) pressed. 1 2 Set the [MONO, STEREO] selector switch to [STEREO]. Turn the [BALANCE] control. The sound’s left/right balance changes according to the direction in which the [BALANCE] control is turned and its position. ! Rotating to the rightmost position outputs only the right sound of stereo audio. Rotating to the leftmost position outputs only the left sound of stereo audio. Audio is output from the [BOOTH] terminal Turn the [BOOTH MONITOR] control. Adjusts the level of audio signals output at the [BOOTH] terminal. En 15
Download PDF file