Mixer section 12 12 12 12 3 4 5 5 6 7 8 9 a c d 44 e f g hi j b 3 5 4 5 6 7 8 9 a 1 FX 1 assign button Turns effect unit FX1 on and off for the respective channel. 2 FX 2 assign button Turns effect unit FX2 on and off for the respective channel. 3 TRIM control Adjusts the individual channel output gain. 4 EQ (HI, MID, LOW) controls Boosts or cuts frequencies for the different channels. 5 Channel Level Indicator Displays the sound level of the respective channels before passing through the channel faders. 6 COLOR control This changes the parameters of the SOUND COLOR FX of the different channels. 7 Headphones CUE/MIC TALK OVER button Press: The sound of channels for which the headphones [ CUE ] button is pressed is output to the headphones. ! When the headphones [ CUE ] button is pressed again, monitoring is canceled. When the [ INPUT SELECT ] switch for channel 3 or 4 is set to [ MIC1 ] or [ MIC2 ], the talkover function can be turned on or off. When the talkover function is on, the headphones [ CUE / MIC TALK OVER ] but- ton flashes. When a sound of over –15 dB is input to the microphone, the sound other than that of the microphone is attenuated by approximately 20 dB. ! The talkover function for both the microphone connected to the [ MIC1 ] ter- minal and the microphone connected to the [ MIC2 ] terminal can be turned on and off by pressing the headphones [ CUE / MIC TALK OVER ] button for either channel 3 or channel 4. [ SHIFT ] + press: The track’s tempo can be set by tapping the button. (Tap function) 8 Headphones CUE button Press: The sound of channels for which the headphones [ CUE ] button is pressed is output to the headphones. ! When the headphones [ CUE ] button is pressed again, monitoring is canceled. [ SHIFT ] + press: The track’s tempo can be set by tapping the button. (Tap function) 9 Channel fader Move: Adjusts the level of audio signals output in each channel. [ SHIFT ] + move: Use the channel fader start function. = Using the channel fader start function (p.22) 12 En a Crossfader Assign Switch Assigns the channel output to the crossfader. [ A ]: Assigns to [ A ] (left) of the crossfader. [ B ]: Assigns to [ B ] (right) of the crossfader. [ THRU ]: Selects this when you do not want to use the crossfader. (The signals do not pass through the crossfader.) ! If microphone sound is selected using the [ INPUT SELECT ] switch of chan- nel 3 or channel 4, even through the crossfader assign switch is switched, the sound of that channel cannot be assigned to the crossfader. b Crossfader Outputs the sound assigned with the crossfader assign switch. [ SHIFT ] + move: Uses the crossfader start function. = Using the crossfader start function (p.22) c MASTER LEVEL control Adjusts the master sound level output. d Master level indicator Displays the master output’s audio level. e BOOTH MONITOR LEVEL control Adjusts the level of audio signals output from the [ BOOTH OUT ] terminal. f SOUND COLOR FX buttons Turns SOUND COLOR FX on and off. g MASTER CUE button Turns monitoring of the master output’s sound on and off. h SAMPLER SYNC button Synchronizes the sampler deck’s tempo with the master deck’s tempo. ! Only a sampler slot with the PLAY mode set to [ Loop ] synchronizes the tempo with the master deck’s tempo. [ SHIFT ] + press: Sets the sampler deck as the master for synchronization. i SAMPLER CUE button Turns monitoring of the sampler deck’s sound on or off. [ SHIFT ] + press: Sets the sampler deck’s tempo by tapping the button. ! Only a sampler slot with the PLAY mode set to [ Loop ] will be the same tempo as the BPM value on the sampler panel. j SAMPLER VOLUME fader Adjusts the sampler’s overall sound level.
Download PDF file
Table of contents