Page number 12
䢢 Monitoring sound with headphones Set the positions of the controls, etc., as shown below. Names of controls, etc. Position HEADPHONES MIX control Center HEADPHONES LEVEL control Turned fully counterclockwise 1 Press the headphones [CUE/TAP] button for the channel 1. 2 Turn the [HEADPHONES LEVEL] control. Adjust the sound level output from the headphones to an appropriate level. Note This unit and the Serato DJ software include a variety of functions enabling individualistic DJ performances. For details on the respective functions, see the operating instructions and the Serato DJ software manual. This unit’s operating instructions can be downloaded from the Pioneer DJ support site. For details, see Downloading this unit’s oper- ating instructions (p. 14). The Serato DJ software manual can be downloaded from Serato. com. For details, see Downloading the Serato DJ software manual (p. 14). Browser section 12 1 3 4 1 LOAD button 2 Rotary selector 3 BACK (VIEW) button 4 LOAD PREPARE (AREA) button Deck section This section is used to control the four decks. The buttons and controls for operating decks 1 and 3 are located on the left side of the controller, those for operating decks 2 and 4 are located on the right side of the controller. Quitting the system 1 Quit Serato DJ. When the software is closed, a message for confirming that you want to close it appears on the computer’s screen. Click [ Yes ] to close. 2 Switch the [ON/OFF] switch on this unit’s rear panel to the [OFF] side to turn this unit’s power off. 3 Disconnect the USB cable from your computer. Names of Parts 1 Browser section 2 Deck section 3 Mixer section 4 Effect section 12 En 1 VINYL button 2 Jog dial 3 DECK 1 button The deck on the right side has a [ DECK 2 ] button. 4 DECK 3 button The deck on the right side has a [ DECK 4 ] button. 5 SHIFT button 6 SYNC button 7 CUE button 8 PLAY/PAUSE " button 9 HOT CUE mode button a ROLL mode button b SLICER mode button c SAMPLER mode button d Performance pads e PARAMETER button, PARAMETER button f Beat indicator g 1/2X (IN) button h 2X (OUT) button i AUTO LOOP button j PAD PLUS ON button k PAD PLUS TAP button l KEY LOCK button m SLIP button n TEMPO slider
Page number 13
English Mixer section 1 Front panel 1 a 2 2 1 23 4 b 1 HEADPHONES LEVEL control 2 CROSS FADER REVERSE switch 3 CROSS FADER CURVE control 4 MIC LEVEL control 3 c 3 46 4 Rear panel 7 5 5 9 8 1 TRIM control 2 EQ ( HI , MID , LOW ) controls 3 FILTER control 4 Headphones CUE / TAP button 5 Channel fader 6 Level indicator switch 7 Level indicator 8 Crossfader 9 CROSS FADER REVERSE indicator a MASTER LEVEL control b HEADPHONES MIX control c SAMPLER VOLUME control Effect section This section is used to control the two effect units (FX1 and FX2). Controls and buttons to operate the FX1 unit are located on the left side of the controller, those to operate the FX2 unit are located on the right side of the controller. 1 23 4 5 6 1 23 4 1 AUX IN LEVEL control 2 BOOTH LEVEL control 3 BOOTH/MASTER selector switch 4 ON/OFF switch About the controls’ setting values The setting values of the controls, etc., below are controlled individually for the respective decks in the Serato DJ software. TRIM control EQ ( HI , MID , LOW ) controls FILTER control Channel fader TEMPO slider If the values controlled by Serato DJ when the decks are switched differ from the positions of this unit’s controls, faders, etc., the controls, fad- ers, etc., must be moved to the positions corresponding to the values controlled by Serato DJ before they will operate. The default values for decks 3 and 4 in Serato DJ are the center position for the [ TRIM ] controls, [ EQ ( HI , MID and LOW )] controls and [ FILTER ] controls, ±0.0% for [ TEMPO ] sliders, and the frontmost position for the channel faders. 789a 1 FX ASSIGN 1 buttons 2 FX ASSIGN 2 buttons 3 Effect parameter 1 control 4 Effect parameter 2 control 5 Effect parameter 3 control 6 FX BEATS control 7 Effect parameter 1 button 8 Effect parameter 2 button 9 Effect parameter 3 button a TAP (FX MODE) button En 13
