Page number 8
e LOOP OUT button Press: Loop Out Point is set, and loop playback begins. When this button is pressed during loop playback, the loop out point can be fine adjusted using the jog wheel. [ SHIFT ] + press: Cancels loop playback. (Loop Exit) After loop playback is canceled, playback returns to the previously set loop in point and loop playback resumes. (Reloop) f LOOP IN button Press: Loop In Point is set. When this button is pressed during loop playback, the loop in point can be fine adjusted using the jog wheel. [ SHIFT ] + press: The loop slot switches. When loops are stored in loop slots ahead of time, they can be called out later. ! Up to 8 loops can be set in the loop slots. ! When you select the loop slot number at which you want to store the loop then set a loop, the loop is automatically stored. ! When a new loop is set after a loop has been stored, the loop is overwritten and the slot is updated. ! When the number of the loop slot whose loop you want to call out is selected and the [ LOOP OUT ] button is pressed while pressing the [ SHIFT ] button (reloop), playback of the stored loop starts. Press for 1 second or longer: Turns the auto 4-beat loop on. g PARAMETER button, PARAMETER button Sets a parameter for the loop roll, slicer, sampler and other functions. = “Using the performance pads” (p.20) h Performance pads Control the hot cue, loop roll, slicer, sampler and other functions. = “Using the performance pads” (p.20) i PLAY/PAUSE f button Press: Play/pause tracks. [ SHIFT ] + press: Returns to the temporary cue point and playback starts. (Stutter) j CUE button Press: This is used to set, play and call out temporary cue points. ! When the [ CUE ] button is pressed while pausing, the temporary cue point is set. ! When the [ CUE ] button is pressed during playback, the track returns to the temporary cue point and pauses. (Back Cue) ! When the [ CUE ] button is pressed and held after the track returns to the temporary cue point, playback continues as long as the button is pressed in. (Cue Sampler) ! When the [ PLAY/PAUSE f ] button is pressed during cue sampling, playback continues from that point. [ SHIFT ] + press: Loads the previous track in the library panel. (Previous Track) ! If the current playback position is not at the beginning of a track, the track returns to the beginning. k HOT CUE mode button Press: Sets the hot cue mode. [ SHIFT ] + press: Sets the cue loop mode. Press for 1 second or longer: Sets the saved flip mode. For details, refer to “Serato Flip manual” under [ Software Info ] on the following Pioneer DJ support site. pioneerdj.com/support/ l ROLL mode button Press: Sets the roll mode. [ SHIFT ] + press: Sets the saved loop mode. Press for 1 second or longer: Sets the edit grid mode. = “Using the edit grid” (p.23) m SYNC button Press: The tempos (pitches) and beat grids of tracks on multiple decks can be synchronized automatically. [ SHIFT ] + press: Cancels the sync mode. n QUANTIZE button Turns on/off the quantize. o SHIFT button When another button is pressed while pressing the [ SHIFT ] button, a different function is called out. p DECK button Press: Switches the deck to be operated. Pressing the [ DECK3 ] button while holding down the [ DECK1 ] button or pressing the [ DECK1 ] button while holding down the [ DECK3 ] button: Turns on DUAL DECK mode on the left deck. Pressing the [ DECK4 ] button while holding down the [ DECK2 ] button or pressing the [ DECK2 ] button while holding down the [ DECK4 ] button: Turns on DUAL DECK mode on the right deck. q KEY DOWN/RESET button Press: Turns down the key. [ SHIFT ] + press: When pressing during KEY SYNC, the key is resumed. p and q buttons are supported to the Pitch’n Time function. To use this function, the activation is required. For details, refer to “Serato Pitch’n Time manual” under [ Software Info ] on the following Pioneer DJ support site. pioneerdj.com/support/ r KEY UP/SYNC button Press: Turns up the key. [ SHIFT ] + press: Changes the key to same as another deck. 8 En
Page number 9
Part names and functions s CENSOR button Press: The track is played in the reverse direction while the [ CENSOR ] button is pressed, and normal playback resumes when the button is released. ! Even during playback in the reverse direction, normal playback continues in the background. When the button is released, playback resumes from the point reached in the background. [ SHIFT ] + press: The track is played in the reverse direction. When the [ SHIFT ] and [ CENSOR ] buttons are pressed again, reverse playback is canceled and normal playback resumes. Mixer section 1 Input select switch Selects the input source of each channel from the components connected to this unit. — [ USB A ] or [ USB B ]: Select to use the track loaded in the Serato DJ Pro software’s deck. — [ MIC1 ] or [ MIC2 ]: Select one of these to use the microphone connected to the [ MIC1 ] or [ MIC2 ] terminal. — [ PHONO/LINE ]: Selected when using an phono level (for MM cartridge) output device such as an analog turntable connected to the [ PHONO/LINE ] input terminals. — The sound is muted for approximately 3 seconds when switched to [ PHONO ]. — [ LINE ]: Select this to use a line level output device (DJ player, etc.) connected to the [ PHONO/LINE ] input terminals. 2 TRIM control Adjusts the individual channel output gain. 3 EQ (HI, MID, LOW) controls Boost or cut frequencies for the different channels. 4 Channel Level indicator Displays the sound level of the respective channels before passing through the channel faders. 5 COLOR controls Change the parameter of SOUND COLOR FX for each channel. En 9
