Page number 8
Cautions on using the iPhone/iPad stand ! This stand is exclusively for use with an iPhone/iPad. Do not place tablets other than iPads or large devices on the stand. ! Set the iPhone/iPad on the stand in the horizontal direction. It may be unstable if set in the vertical direction. ! Do not apply excessive force to the stand. Doing so may damage this unit. ! Please note that Pioneer will accept no responsibility whatsoever for damage to or malfunction of the device, injury, etc., due to the device falling, etc. ! Do not move with an iPhone/iPad placed on the stand. The iPhone/ iPad could fall off. ! If there is a cover on the iPhone/iPad, remove the cover before plac- ing the iPhone/iPad on the stand. If the cover is left on, the iPhone/ iPad could be unstable. iOS devices that can be used with this unit and placed on the stand ! iOS iOS 6 ! Devices supporting the iPhone/iPad connection cable (Lightning) iPad (4th generation), iPad mini, iPhone 5, iPod touch (5th generation) For the latest information on iOS devices, see [ DDJ-WeGO2 ] on the Pioneer DJ support site below. http://pioneerdj.com/support/ Connecting with an iPhone/iPad Connect with the triangle mark at the top. DJ software iPhone/iPad ON/OFF switch iPhone/iPad connection cable (Lightning) ON OFF For checking the output sound Headphones F 電 or 源 po 供 w 給 er 用 supply USB mobile battery/ USB power adapter MASTER OUT MIC R R L L For audio input Microphone For audio output Component, amplifier, powered speaker, etc. Connections Be sure the power is off when connecting equipment and changing connections. Be sure to use the USB cable included with this product. Refer to the operating instructions for the component to be connected. Connecting with a computer ! The iPhone/iPad connection has priority, so do not connect an iPhone/iPad when using a computer. ! VIRTUAL DJ LE for DDJ-WEGO2 is customized to output the audio only from the unit not from the computer. Please connect head- phones, an amplifier or powered speakers as shown in the figure below to hear the output sound. Audio output from your computer will be available if a paid upgrade to VIRTUALDJ PRO FULL is completed. With this unit, the power is supplied by USB bus power. The unit can be used simply by connecting it to a computer using the USB cable. ! Connect this unit and the computer directly using the included USB cable. ! Connect the computer to which this unit is to be connected to an AC power supply. ! A USB hub cannot be used. ON/OFF switch ON OFF For checking the output sound Headphones DJ software Computer MASTER OUT MIC R R L L For audio input Microphone For audio output Component, amplifier, powered speaker, etc. ! An iPhone/iPad cannot be charged with the iPhone/iPad connection cable (Lightning). Starting the system When using a computer 1 Connect this unit to your computer via a USB cable. 2 Boot up the connected computer. 3 Slide this unit’s [ON/OFF] switch to the [ON] position. Turn on the power of this unit. Launching VIRTUAL DJ LE About the order of operations when launching VIRTUAL DJ LE Always first turn on this unit’s power, wait for the startup illumina- tion to finish, check that this unit’s [ CTRL A ], [ FX1 ], [ FX2 ], [ FX3 ] and [ CTRL B ] buttons are all lit dimly, then launch VIRTUAL DJ LE. Launching VIRTUAL DJ LE (Windows) From the Windows [Start] menu, click the [All Programs] > [VirtualDJ] > [VirtualDJ LE (DDJ-WeGO2)] icon. Launching VIRTUAL DJ LE (Mac OS X) In Finder, open the [Application] folder, then double- click the [VirtualDJ LE] icon. When VIRTUAL DJ LE is launched the first time, a screen for entering the serial number appears. Input the serial number printed on this unit’s bottom panel ( XXXX- XXXX-XXXXX/WEGO2 ), then click [ OK ]. 8 En
Page number 9
English When using an iPhone/iPad Audio disorders (beeping) may occur in this unit when calling or send- ing/receiving data on the mobile phone. This problem can arise when the mobile phone’s communications protocol is GSM, and is due to interference caused by GSM. If this happens, change the iPhone/iPad’s setting to flight mode. This problem does not occur with the 3G or LTE communications protocols. 1 Connect the iPhone/iPad with this unit using the iPhone/iPad connection cable (Lightning). 2 Connect this unit with the USB mobile battery or USB power adapter. 3 Slide this unit’s [ON/OFF] switch to the [ON] position. 4 Launch the DJ application on the iPhone/iPad. Basic Operation D CC A BD ! The curve characteristics can be switched using the crossfader curve setting button on the [ MIXER ] panel at the center of the com- puter’s screen. — [ ]: Select this when you do not want to use the crossfader. — [ ]: Set here for a curve that rises gradually. — [ ]: Sets an abruptly rising curve. 3 Turn the [MASTER VOL] control to adjust the audio level of the speakers. Monitoring sound with headphones ( r C) 1 Connect headphones to the [PHONES] terminal. 2 Press the [CUE ] button for the deck you want to monitor. 3 Turn the [HEADPHONES MIX] control. ! Turn counterclockwise: The volume of the deck whose [ CUE ] but- ton is pressed increases relatively. ! Turn clockwise: The [ MASTER OUT ] volume increases relatively. 4 Turn the [HEADPHONES VOL] control. ! The sound of the deck whose [ CUE from the headphones. ] button is pressed is output ! When the [ CUE ] button is pressed again, monitoring is canceled. Quitting the system 1 Quit VIRTUAL DJ LE. 2 Slide this unit’s [ON/OFF] switch to the [OFF] position. B 3 Disconnect the USB cable from your computer. Loading tracks and playing them ( r A) 1 Turn the rotary selector while pressing the [SHIFT] button to select a folder or item. ! When a folder or item with the [+] mark is selected and the rotary selector is pressed while pressing the [ SHIFT ] button, that folder or item is opened or closed. 2 Release the [SHIFT] button then turn the rotary selector to select the track. 3 Press the [LOAD] button to load the selected track onto the deck. 4 Press the [ f ] button to play the track. ! When this button is pressed again during playback, playback pauses. Using the mixer functions ( r B) ! Adjust the volume of the powered speakers, etc., connected to the [ MASTER OUT ] terminals to an appropriate level. Note that if the volume is set too high, the output sound could be very loud. 1 Operate the channel faders to adjust the audio level output from the respective decks. 2 Operate the crossfader to switch the deck whose sound is output from the speakers. — Left edge: Sound is output from deck [ A ] or [ C ]. — Center: The sound of all the decks is mixed and output. — Right edge: Sound is output from deck [ B ] or [ D ]. En 9
