Page number 6
Installation and Connections How to Install A speaker’s playback sound is delicately influenced by conditions in the listening room. To produce optimum listening conditions, take due consideration of the conditions of your installation location before beginning actual installation. Place the speakers at ear level. Speakers should ideally be located at 30 ° angles from the listening position (together forming a total 60 ° angle), and rotated inward to face the listening position. 50 °～ 60 ° For a natural stereo effect, the right and left speakers should be installed in symmetrical and equidistant positions from the listening position. CAUTION To promote proper cooling, please assure that sufficient space is preserved between the speakers and nearby walls or other components (minimum 30 cm or more above, behind, and to right and left sides of each speaker). Leaving insufficient space between the speaker and walls or other components may lead to rising interior temperatures, leading to malfunction or damage. Connections When making or changing connections, always turn off the power and disconnect the power cord from its outlet. Also, be sure to read the operating instructions for the other components to which you are connecting these speakers. Do not plug in the power cord until all other connections have been completed. Use only the furnished accessory power cord. • Do not connect to both the XLR INPUT connector and the TRS INPUT jack at the same time. • Make sure to set the sound level at an appropriate level as the input signals to the XLR INPUT connector (or TRS INPUT jack) and RCA INPUT jack will be mixed together, affecting the sound level. Additional Information Troubleshooting If you think you are experiencing a malfunction with this unit, check the following items. Also check other devices connected to the unit. If the problem persists, consult your dealer for service. On occasion, the unit may fail to operate properly due to static electricity or other external conditions. In this event, disconnect the power cord and wait for five minutes or more, then reconnect the power cord and check for proper operation. Symptom No power No sound from connected audio devices, or sound is very small. Illumination (POWER indicator) remains turned off. Speakers do not resume (turn on) from standby mode. Sound is distorted. Feedback (continuous howling sound) Items to Check Is power cord connected properly? Has connected audio device been set properly? Is connection cable connected properly? Are connectors or plugs dirty? Is the sound volume set properly? Is the power turned on? Is the auto standby function on? Is the power turned on? Is the auto standby function on? Is the level of the input signal low? Is the sound level set properly? Is the output level of the connected audio device set properly? Is the sound volume set properly? Remedy Connect power cord to outlet. Set device’s external input and sound volume properly. Connect cables properly. Clean connectors and plugs before connecting. Turn the [ LEVEL ] dial on the rear panel clockwise and turn up the volume. Turn on the [ POWER ] switch on the rear panel. Turn off the [ POWER ] switch on the rear panel once, wait a few seconds, and then turn it back on. Turn on the [ POWER ] switch on the rear panel. Turn off the [ POWER ] switch on the rear panel once, wait a few seconds, and then turn it back on. Increase the level of the input signal. Turn off the [ AUTO STANDBY ] switch to turn off the auto standby function. Slowly turn the [ LEVEL ] dial on the rear panel counterclockwise and turn down the volume. Adjust the output level of the connected audio device properly. Slowly turn the [ LEVEL ] dial on the rear panel counterclockwise and turn down the volume. 6 En
Page number 7
English Trademarks Pioneer is a registered trademark of PIONEER CORPORATION. Other listed company names and a product name are the registered trademark of the companies or trademarks. Specifications S-DJ50X/S-DJ50X-W S-DJ60X Type Bi-amp 2-way active speaker Amplifier LF amp 30 W 50 W HF amp 15 W 20 W Input connectors (balanced input) XLR × 1, TRS (1/4 inch Phone) × 1 Input connectors (unbalanced input) RCA × 1 Impedance 10 kΩ Speaker Enclosure Bass reflex Enclosure material MDF Woofer (LF driver) 13 cm cone 15 cm cone Tweeter (HF driver) 2.5 cm soft dome Playback response 50 Hz to 20 kHz 45 Hz to 20 kHz Power unit/other Supported voltages 100 V to 120 V (50 Hz to 60 Hz) / 220 V to 240 V (50 Hz to 60 Hz) conversion Power consumption 100 W 140 W Pmoowdeer consumption during standby 0.5 W or less External dimensions W × H × D 197 mm × 301 mm × 262 mm 228 mm × 342 mm × 295 mm Weight 6.5 kg 8.5 kg S-DJ80X 70 W 20 W 20 cm cone 40 Hz to 20 kHz 160 W 276 mm × 401 mm × 315 mm 11.8 kg Specifications and design subject to possible modification without notice, due to improvements. © 2013 PIONEER CORPORATION. All rights reserved. En 7
